Welcome to Shenzhen Sing Fung Intelligent Manufacturing Co., Ltd.
E-mail：shaobo@sfi-crf.com
News
Several points to be noted in the planning of low-temperature plasma power integrity power system
- Categories:Technical Support
- Author:Plasma cleaning machine-CRF plasma plasma equipment-plasma surface treatment machine manufacturer-chengfeng intelligent manufacturing
- Origin:
- Time of issue:2022-01-07
- Views:
(Summary description)Several points to be noted in the planning of low-temperature plasma power integrity power system: Analysis of low-temperature plasma power integrity power system noise margin Most chips will give a normal operating voltage range, usually ±5%. The output voltage accuracy of the traditional voltage stabilizer is generally ±2.5%, so the peak amplitude of the power supply noise should not be greater than ±2.5%. Accuracy is conditional, including load conditions, working temperature and other restrictions, so there must be margin. Second, the calculation of the noise margin of the low-temperature plasma power supply of the whole machine. For example, the normal working voltage of the chip is 3.13V to 3.47V, and the nominal output of the voltage regulator chip is 3.3V. The whole machine is installed on the circuit board, and the power supply voltage regulator chip of the whole machine outputs 3.36V. Then, the allowable voltage change range is 3.47-3.36=0.11V=110 millivolts. The output accuracy of the voltage stabilizer is ±1%, that is, ±3.363*1%=±33.6 mV. The power system noise margin is 110-33.6=76.4 millivolts. 3. How does the power supply noise of the low-temperature plasma power supply rectifier generate? The output of the stabilized power supply chip itself is unstable and will fluctuate to a certain extent. The second is that the regulated power supply cannot respond to the rapid changes in the current requirements of the load in real time. The rectifier power supply stabilized power supply chip senses the change of its output voltage and adjusts its output current to return it to the rated output voltage. Third, the voltage drop caused by the load transient current on the impedance of the power path and the impedance of the ground path. The pins and pads themselves will have parasitic inductance. When the transient current flows through the channel, a voltage drop will inevitably occur. Therefore, power integrity Therefore, the voltage at the power supply pin of the load chip will fluctuate with the change of the transient current, which is the power supply noise generated when impedance occurs.
Several points to be noted in the planning of low-temperature plasma power integrity power system
(Summary description)Several points to be noted in the planning of low-temperature plasma power integrity power system:
Analysis of low-temperature plasma power integrity power system noise margin Most chips will give a normal operating voltage range, usually ±5%. The output voltage accuracy of the traditional voltage stabilizer is generally ±2.5%, so the peak amplitude of the power supply noise should not be greater than ±2.5%. Accuracy is conditional, including load conditions, working temperature and other restrictions, so there must be margin.
Second, the calculation of the noise margin of the low-temperature plasma power supply of the whole machine.
For example, the normal working voltage of the chip is 3.13V to 3.47V, and the nominal output of the voltage regulator chip is 3.3V. The whole machine is installed on the circuit board, and the power supply voltage regulator chip of the whole machine outputs 3.36V. Then, the allowable voltage change range is 3.47-3.36=0.11V=110 millivolts. The output accuracy of the voltage stabilizer is ±1%, that is, ±3.363*1%=±33.6 mV. The power system noise margin is 110-33.6=76.4 millivolts.
3. How does the power supply noise of the low-temperature plasma power supply rectifier generate?
The output of the stabilized power supply chip itself is unstable and will fluctuate to a certain extent. The second is that the regulated power supply cannot respond to the rapid changes in the current requirements of the load in real time. The rectifier power supply stabilized power supply chip senses the change of its output voltage and adjusts its output current to return it to the rated output voltage. Third, the voltage drop caused by the load transient current on the impedance of the power path and the impedance of the ground path. The pins and pads themselves will have parasitic inductance. When the transient current flows through the channel, a voltage drop will inevitably occur. Therefore, power integrity Therefore, the voltage at the power supply pin of the load chip will fluctuate with the change of the transient current, which is the power supply noise generated when impedance occurs.
- Categories:Technical Support
- Author:Plasma cleaning machine-CRF plasma plasma equipment-plasma surface treatment machine manufacturer-chengfeng intelligent manufacturing
- Origin:
- Time of issue:2022-01-07 22:54
- Views:
Information
Several points to be noted in the planning of low-temperature plasma power integrity power system:
Analysis of low-temperature plasma power integrity power system noise margin Most chips will give a normal operating voltage range, usually ±5%. The output voltage accuracy of the traditional voltage stabilizer is generally ±2.5%, so the peak amplitude of the power supply noise should not be greater than ±2.5%. Accuracy is conditional, including load conditions, working temperature and other restrictions, so there must be margin.
Second, the calculation of the noise margin of the low-temperature plasma power supply of the whole machine.
For example, the normal working voltage of the chip is 3.13V to 3.47V, and the nominal output of the voltage regulator chip is 3.3V. The whole machine is installed on the circuit board, and the power supply voltage regulator chip of the whole machine outputs 3.36V. Then, the allowable voltage change range is 3.47-3.36=0.11V=110 millivolts. The output accuracy of the voltage stabilizer is ±1%, that is, ±3.363*1%=±33.6 mV. The power system noise margin is 110-33.6=76.4 millivolts.
3. How does the power supply noise of the low-temperature plasma power supply rectifier generate?
The output of the stabilized power supply chip itself is unstable and will fluctuate to a certain extent. The second is that the regulated power supply cannot respond to the rapid changes in the current requirements of the load in real time. The rectifier power supply stabilized power supply chip senses the change of its output voltage and adjusts its output current to return it to the rated output voltage. Third, the voltage drop caused by the load transient current on the impedance of the power path and the impedance of the ground path. The pins and pads themselves will have parasitic inductance. When the transient current flows through the channel, a voltage drop will inevitably occur. Therefore, power integrity Therefore, the voltage at the power supply pin of the load chip will fluctuate with the change of the transient current, which is the power supply noise generated when impedance occurs.
Scan the QR code to read on your phone
Relevant Information
The energy range of the plasma is very wide. There is no choice for the excitation or ionization of electrons
2022-01-06 14:11
The importance of plasma plasma processor cleaning organic field effect transistor (OFET) materials
2022-01-05 17:19
Plasma etching cleaning machine ICP etching technology is widely used in SiC etching applications
2022-01-04 16:56
Study on the experimental nucleation of plasma chemical vapor deposition diamond film
2022-01-03 16:55
Removal of pollutant molecules in the production process of microelectronics packaging of plasma processing equipment
2022-01-02 15:27
The low-temperature plasma has enough energy to break the chemical bonds in the biomass feedstock
2021-12-31 15:24
Plasma glass cleaning machines are widely used in manufacturing industries such as mobile phone coating and new materials
2021-12-30 15:22
The plasma generator power supply chooses different process gas classification and action mechanism
2021-12-29 19:55
The bonding and other processes can only be implemented after the metal plastic activation treatment of the oxygen plasma cleaner
2021-12-28 19:54
TEL：0755-3367 3020 / 0755-3367 3019
E-mail：sales-sfi@sfi-crf.com
ADD：Mabao Industrial Zone, Huangpu, Baoan District, Shenzhen
